The following changes have been made since version since version 4.46:

Improvements:

• Add framing options and enhanced frame format functions in the ISO14443 Reader API (see programming guide)
• Analyzer ISO-14443 have been updated to handle ISO14443-4 features :
• Is now able to analyze frame with framing options (Type A and B)
• Is now able to analyze frame with FEC encoding (Type A and B)

Fixes:

• Remove duplicated popup when autotest failed
• Autotest will now only be performed at the first connection of ProxiLAB
• PowerLevel has been replaced by PowerLevelPercent in configuration file

Improvements

• Self-control mechanism during the Power-up sequence added
• ISO14443: reader and emulator handle FSC/FSD up to 4096 bytes (256 bytes before)
• JISX6319 : PICC demodulation
• ISO15693 : PICC and PCD decoding
• ISO18092 : ProxiLAB should be able to send a RSL_REQ without DID field
• Spy logger handle frames up to 4096 bytes (1024 bytes before)
• Power level can now be specified in percent for more precision
• A residual power field can be specified when RF is off
• Maximum waveform overshoot is up to 200% of high level (125% of low/high level before)
• API functions for ALM (Active Load Modulation) and subcarriers
• VNA : reduced calibration save and reload time, new enable/disable port extension API

 Fixes

• ISO15693: TX logger in emulator mode (first byte of PICC frame not logged)
• AWG noisy output (due to DAC configuration)
• JISX6319: Some Write commands were analyzed as UNDECODED FRAME even though they were correctly formatted
• Administrator mode is not required anymore to update ProxiLAB licenses with a .key file
• Some ISO14443 Type B frames were mistakenly decoded as Innovatron (B prime) frames
• ISO14443-B analyzer : analysis of ATTRIB command will now display correct warning messages
• ISO14443-B analyzer : glitch under 20us are ignored
• ISO18092 analyzer : the warning "Bits b4-b7 shall be set to 0, all other values are RFU" was wrongly displayed for ATR_RES frames
• ISO18092 : bitrate management fix
• APDU : details now available in description view
• S-Param : correctly displayed in description view
• ISO15693 : PCD frame length should not vary with pause length
• ISO15693 : fixed CRC computation in description view
• ISO14443 : the warning "Bit b4 of PCB is set but CID is not present" was wrongly displayed

Known limitations:

• This version of ProxiLAB software does not support PCSC features

Before updating your equipment, and due to the self-control mechanism during the power-up sequence, make sure you have returned your equipment for the annual control & calibration. Please contact our support team for more information support@keolabs.com.

Improvements:
. Windows 10 signed Driver
. PCD ISO14443A/B : adjust Tload and Tnn timing for Negative Load Modulation
. PCD ISO14443B : Enable EGT decoding before EOF
. PCD Demodulation enhancement
. Add advanced event on analog trace triggers
. Dual Antenna support
. PCD-VNA Antenna support

Fixes:
. Trigger 1 SMA Output
. NFC Forum T1T emulator
. ISO18092 P2P Passive

Improvements:

• Improvement for the carrier frequency parameter (from 0 to 60MHz with a step of 1Hz)
• New PCD demodulator architecture
• Reader commands can be sent in card emulation mode
• New dedicated triggers for analog trace

Fixes:

• PCD ISO14443 : decoding issue fixed after VHBR speed downgrade trough s-parameter
• VCD ISO15693 : 1 over 255 coding issue
• VICC ISO15693 : 1 over 255 decoding issue
• PICC ISO14443 : SWTX timing accuracy improvement
• Sequential trigger improvement

Improvements:

• Possibility to append the last EGT before EOF of a PCD when Reader Type B mode
• EMVCo PICC & PCD features for test case implementation
• PICC emulator demodulation

WARNING:

• This version has been validated on ProxiLAB Quest only and does not officially support ProxiLAB V3. 
• This version does not support EMVCo Digital test suites. The 4.38 version will be released soon.

Improvements:

• Initiator and Target ISO18092 Active mode support
• Possible to append the last EGT before EOF of a PICC when Emulator Type B mode
• Reader ISO15693 GetLastT1, GetT1Buffer, GetT1BufferLength and ClearT1Buffer functions
• Reader ISO15693 pulse duration improvement

Fixes:

• Reader demodulation issues

WARNING: This version has been validated on ProxiLAB Quest only and does not support officially ProxiLAB V3. Use with ProxiLAB V3 at your own responsibility.

Improvements:

. Reader ISO14443 VHBR 1695/3390/6780 kbps support
. Reader ISO14443 TypeA SendTransparentCommand function PARITY_BITS mode
. Reader ISO14443 TypeA SendTransparentCommandBits function
. Reader ISO14443 TypeA GetLastFDT, GetFDTBufferLength and ClearFDTBuffer functions
. Reader ISO14443 TypeB GetLastTR0, GetTR0BufferLength and ClearTR0Buffer functions
. Reader ISO15693 SendCommand function
. PICC decoding after a Spulse PCD frame when Reader mode

Fixes:
. Reader ISO15693: PCD glitch, pause duration, TimeOut and StayQuiet flag
. Emulator ISO15693: PCD decoding when pause duration is 6 us
. Timer measurement mode instability
. When two Spulse frames are preloaded, the state between two Spulse frames stays at 0

Support of ProxiLAB Quest hardware

Improvements:

. Emulator.ISO14443.WaitAndGetFrame timeout improved
. Emulator ISO14443 847kbps demodulation
. Reader ISO14443 4kB PICC frame decoding

Fixes:
. No more EGT before EOF in ISO14443-B
. CID bit in PCB when chaining Iblock in ISO14443 emulator
. Emulator.ISO14443.WaitAndGetFrame chaining processing when a RF reset occurs in between

ProxiLAB 3.22.15.0710 (Released 2015/07/10)
-------------------------------------------

Improvements:

. Sequencer and Spulse are common to reader and emulator in API
. Added sequencer/spulse appnote

. Reader ISO14443 SSB filter improvement
. Reader ISO14443 reader waveform is now up to 128 points (rising and
falling edge)
. Reader ISO14443 card response amplitude gage to on all demodulation
input (polling)
. Reader ISO15693 Reader decoding improvement

. Emulator ISO15693 AppendSOF and AppendEOF property
. Emulator ISO15693 Single/Dual subcarrier property
. Emulator ISO15693 High/low datarate property
. Emulator ISO15693 InventoryResponseSlots property
. Emulator ISO18745 S-Parameters handling
. Emulator ISO14443 PIXCC to PCD FDT min/TR2 min supported
. Emulator ISO14443 cascade level 2 or 3 supported

Fixes:
. SFGI handling
. PCSC timeout management
. SWTX handling
. FELICA processing time precision
. PCSC GUI blocking I2C
. LoadSWTX accuracy
. ProxiLAB.Trigger.GetTrigger

Improvements:
. Field measurements is available through SMA4 on calibrated devices.
. Supports NFC LLCP and SNEP.
. Implement SSB filters in Reader A/B mode.
. Automatic SWTX command handling with configurable FDT in sequencer.
. GUI message changed to Python language.
. Improved PICC timeout management in Reader Felica mode.
. Improved Reader Felica time slot number management in Reader Felica
mode.
. Improved SendTclCommand management: If card stay mute during chained
I-block transmission RNACK is sent.
. Possibility to send Felica response with positive modulation in
Emulator Felica mode.
. Possibility to send Felica command with positive modulation in
Reader Felica mode.
. Possibility to inverse Felica command polarity in Reader Felica mode.

Fixes:
. Basic Event trigger for ProxiLAB V2.
. PICC_CRC_ERROR trigger for Emulator A/B mode.

ProxiLAB 3.18.14.0428 (Released 2014/04/28)
-------------------------------------------

Improvements:
. Ajusted 3 etus delay for trace signals when RF_in demodulation is
activated
. Improved PICC 212/424/847kbps frames decoding
. Improved carrier frequency accuracy
. Security Pulse can be applied to loading effect of PICC-Probe+ for
test EMD

Fixes:
. PCSC mode: SFGI management

Improvements:
. Improved sampling and demodulation performance
. Improved logger behavior
. Improved timings accuracy
. New filters topology for PICC demodulation
. Added PCD_FRAME_FELICA_212/424 into SMA
. Improved low power waveform generation

Fixes:
. repaired PCSC drivers
. type A: use correct Layer (3 or 4) FDT when calling event_response method

Complex triggers are now available via GUI
Splitted reader bitstream: Reader_AB/Reader_ISO15693/Reader_JISX6319

Fixes:
. Fixed bug on I-block numbering
. Improved I-block decoding in PCD TypeA 424kb
. Fixed Spulse timmings
. WritePicoData now works in sequencer
. Fixed chained IBlock management
. Fixed CID management
. Fixed Frame type during PPS response
. Able to send Felica frame > 255 bytes (reader and Emulator)
. Fixed PatternTiming when ParityError is activated

Improvements:
. Improve FDT precision when mode PCD EOF
. improve ProcessingTime precision
. Enlarged Reader's transmission and reception FIFO to 4Kb
. Improved TypeA sampling
. implementation of improved PICC IO filter
. Added ability to enter CRC manually in LoadHLTBResponse function
. Removed some glitches in PICC response (TypeB)
. Minimum FDT of Spulse changes from 2 to 3
. Improved LoadSAKI and LoadSAKC RGPA message management
. Improved LoadHLTBResponse: when AppendCRC=0, HLTB response has 1 byte + 2 bytes of CRC = 3 bytes

ProxiLAB becomes a KEOLABS tool

Fixes:
. Fixed Reader TypeA.FallingEdgeWaveForm
. Fixed minor bugs in HMI and output window
. Added default settings button JISX6319 and ISO15693 tabs
. Fixed trigger trace channel display in RGPA
. Fixed RF power trace channel display in RGPA in PICC emulator when
field present before trace starting
. 3.4 and 6.8 Mbit/s VHBR demodulation improvement in reader emulator
mode
. Suppressed not expected pulse during mute LoadEventResponse
. Automatic script generation now runs for all HMI commands

Improvements:
. Increased sequencer FIFO from 2048 to 4096 bytes.
. Automatic bitrate detection in Felica PICC emulator mode.
. Added PICC emulator Security Pulse (EnableSpulse and LoadSpulse
functions)
. Added PICC emulator ISO15693 LoadInventoryResponse and AppendCRC
functions.
. Examples are now compatible with regular JScipt.
. New PICC Analog Probe+ taken into account.
. Added C# example.

Patch to apply (fix Type A analog wave form functions) Download the patch file, unzip it, and copy the 2 files into the directory {RGPA}Tools/ProxiLAB/Bin. Reader emulation mode Time-out resolution to 16/fc for all reader mode protocols Demodulation of VHBR at 3.4 Mbits Fixed problems with card polling gauge view Saved power level for next card polling Added "ExternalEnableField" property to simulate some tearing on field power Enhanced command.ini files management : add delete command, multi files management... PICC emulation mode Split of the emulator mode : A/B and Felica/15693 Fixed signal PCD_SOF trace Fixed parity error in high bitrate PICC frames Fixed high bitrate PICC frames analysis Added “LoadEventResponse/EnableEventResponse” function to prepare multiple sendings trigged by event (ISO14443/Felica) Fixed B' response for COM_R/COM-RA command RF IN demodulation is now available in PICC emulation mode by script Common ProxiLAb can run now without Administrator account Added protocol specific PCD frames traces on SMA Fixed Trigger Complex shifting mode, and Autoreload functionality Trigger complex are now usable in sequencer Added ISO14443-APDU channel in analysis Sharing of the description scripts (RGPAprotocol folder) Fixed minor bugs in HMI and output window ProxiLAB V3.2 hardware taken into account

PICC emulator mode :
- Added LoadDefaultConfig functions for PICC emulator protocols
- Fixed Append CRC/LoadATQC for Felica
- Reset Trigger complex if change NbSteps value
- Fixed full collision functionality
- Fixed Error 14339 during IBlock type A with ASK reader
- No more response in emulator mode, if no IBlock loaded

Reader mode :
- Fixed Error 217 on SendTcl
- Fixed bitrate in SendTransparent cde in Felica reader mode with sequencer active
- Field stability improvement at high power level
- Fixed too long timeout in type B SendTransparentCommand function

Common :
- Changed GetFrameType return in accordance with trace displays
- Added triggers on ISO15693 reader and PICC emulator modes
- Added warning message on beta versions
- Fixed analyser type A bug with high bit rates
- Changed ISO15693 PICC colour in RGPA trace
- Minimum delay time functions improvement in Toolbox

Emulator mode:
- Fixed 2770 regression on pattern filters

Common:
- Improvement of "Programming Guide" documentation